PIXHAWK 6C PRO
The Pixhawk® 6C PRO is the latest update to the successful family of Pixhawk® flight controllers, based on the Pixhawk® FMUv6C Open Standard and Connector Standard. It comes with PX4 Autopilot® pre-installed. STMicroelectronics® based STM32H743, paired with sensor technology from Bosch® & InvenSense®, giving you flexibility and reliability for controlling any autonomous vehicle, suitable for both academic and commercial applications.
The Pixhawk® 6C PRO\'s H7 microcontroller contain the Arm® Cortex®-M7 core running up to 480 MHz, has 2MB flash memory and 1MB RAM. Thanks to the updated processing power, developers can be more productive and efficient with their development work, allowing for complex algorithms and models.
The Pixhawk 6C PRO includes high-performance, low-noise IMUs on board, designed to be cost effective while having IMU redundancy. A vibration isolation System to filter out high-frequency vibration and reduce noise to ensure accurate readings, allowing vehicles to reach better overall flight performances.
The Pixhawk® 6C PRO is perfect for developers at corporate research labs, startups, academics (research, professors, students), and commercial application.
Key Design Points
High performance STM32H743 Processor with more computing power & RAM
Build-in Buzzer,Build-in RGB LED,support Independent external Safety Button,With Plastic Case
New cost-effective design with low-profile form factor
Newly designed integrated vibration isolation system to filter out high frequency vibration and reduce noise to ensure accurate readings
IMUs are temperature-controlled by onboard heating resistors, allowing optimum working temperature of IMUs
Technical Specification
Processors & Sensors
FMU Processor: STM32H743
32 Bit Arm® Cortex®-M7, 480MHz, 2MB memory, 1MB SRAM
IO Processor: STM32F103
32 Bit Arm® Cortex®-M3, 72MHz, 64KB SRAM
On-board sensors
Accel/Gyro: ICM-42688-P
Accel/Gyro: BMI055
Mag: IST8310
Barometer: MS5611
Electrical data
Voltage Ratings:
Max input voltage: 6V
USB Power Input: 4.75~5.25V
Servo Rail Input: 0~36V
Current Ratings:
TELEM1 Max output current limiter: 1.5A
All other port combined output current limiter: 1.5A
Mechanical data
Dimensions: 85 * 45 * 10 mm
Weight (Plastic Case) : 33g
433MHZ 500MW :
F350+4 PCS BLHELI 30A +4 pairs self-locking 8045 Propellers +4 PCS 2212 920KV Motor
PIXHAWK 6C PRO+2*PWM Module+I2C Expansion Board RGB LED Module+ Safety Button+4G TF Card+M8N GPS+GPS Holder+Shock Absorber+PM02 V3.2 Power Module(support 12S)+Radio Telemetry V6 433MHZ 500MW
Carbon Fiber 350 Frame
BLHELI ESC:
A.Features
A1: Use authentic electronic components to ensure high quality and enhance the current endurance ability of the ESC.
A2: Based on BLHeli firmware, optimized for high performance with great and much quicker throttle response.
A3: Special designed for multirotors, and compatible with fixed-wing aircrafts and helicopters.
A4: Multiple protection features including Low-voltage cut-off protection / over-heat protection / throttle signal loss protection.
A5: Throttle range can be configured and is fully compatible with all receivers, providing smooth, and precise throttle response. A6: All parameters can be programmed via using a transmitter, including default settings.
B. Productspecification
2212 920KV Motor
8045 Propellers
M8N GPS:
PM02 V3.2 Power Module
For PIXHAWK 2.4.8 :used for PIXHAWK2.4.8 Flight Control
For PIXHAWK 6C :used for PIXHAWK 6C Flight Control
Description:
This PM02 Power Module provides a simple way to supply regulated 5.2V to flight controller from the battery while providing current consumption and battery voltage measurements via analog signal through a 6 Pin JST-GH cable. It comes with pre-soldered wires, capacitor, and XT60 connector on both ends, along with shrink tubing on the PCBA for physical protection.
Specification:
Input Voltage: 2S-12S
PCB Cont. Current Rating: 60A
PCB Burst Current Rating: 100A (<60 Sec)
Max Current Sensing: 120A
Output: DC 5.2V & 3A Max
Voltage Divider: 18.182
Amperes per Volt: 36.364
Weight: 20g
Please Note:
- The XT60 Plug and 12AWG wire that are pre-soldered on the board is rating for 30A continuous current and 60A burst current (< 60 Seconds). If a higher current is being used, the plug type and wire size should be changed accordingly. You can refer to this chart for reference.
Radio Telemetry V6:
I2C:
RGB:
The powerful features of Pixhawk are self-evident. Its integrated RGB full color multifunctional indicator light has high brightness, making it easy to identify flight control status. Compared to previous APMs, it is more intuitive and clear, making it a great design. But the problem lies here: this RGB LED is facing upwards and can only be viewed on the ground, unable to recognize flight control status in the air. Additionally, some racks have a fully enclosed design, such as the SKY-HERO, where the flight control can be hidden between two central boards, making it difficult for users to easily connect USB cables while being well protected. So we referred to the official accessory design and launched this two in one Pixhawk RGB module.
The Pixhawk RGB module has the following characteristics:
·Extend the RGB indicator light to the exterior of the aircraft to display;
·Extend the USB port to facilitate external connection to the USB cable, without being limited by the flight control installation location;
·The Toshiba LED controller and Osram\'s RGB high brightness LED are identical to those on the Pixhawk board;
·Molex original 1.25 connector and HRS original USB socket ensure good contact stability.
Use OLED for PIXHAWK, must follow these steps,
Connect OLED to I2C port of Pixhawk
Upload ardupilot firmware, at least 3.5 version, below 3.5 version will not be display.
Use Mission Planner to modify parameters NTF_DISPLAY_TYPE to 1. After modify, remember to click “Write Params” button.
Now the OLED is only supported for ardupilot firmware,can not be supported PX4 firmware
Reboot the board.
商品備註・物品狀況:全新・最新關注時間:2026-10-17